Replies to This Discussion

Permalink Reply by forumuser on July 5, 2016 at 14:28

Hi John,

Please follow these instructions to get the correct TV3 feed:

Press the Menu Button to bring up the main Menu
Press the Left Arrow until the Installation Menu is displayed then press OK
Select TP Manager and press OK
Press the Down Arrow and select 12456
Press the Blue Button (To Scan)
Press the Right Arrow to select Free Only and press OK

You will need to organise your channels into the correct order after scanning.

Regards, Josh

• ▶ Reply

Permalink Reply by John Jenkins on July 5, 2016 at 16:09

Josh Hill said:

Hi John,

Please follow these instructions to get the correct TV3 feed:

Press the Menu Button to bring up the main Menu
Press the Left Arrow until the Installation Menu is displayed then press OK
Select TP Manager and press OK
Press the Down Arrow and select 12456
Press the Blue Button (To Scan)
Press the Right Arrow to select Free Only and press OK

You will need to organise your channels into the correct order after scanning.

Regards, Josh

• ▶ Reply

Permalink Reply by John Jenkins on July 5, 2016 at 16:18

Hiya Josh...I printed out those same instructions this morning,they don't work...

I press menu..pressing the left arrow does nothing.and that's as far as I can go,I note that the

"Dish'' S7010 is not included in the list

regards jack

• ▶ Reply

Permalink Reply by Paul on July 5, 2016 at 18:05

Try this instead

How to Tune TV3 in on Your DishTV S7000/S7010

Go to Main Menu>Installation>Installation
(At the bottom of your screen you should have Level and Quality bars)

Then push the red button on your remote (this will do a single scan)
Use the left and right arrows on each line to make it look like below.

Scan Mode Free
Program Type TV
Scan Type Manual Scan
NIT Search Off

Then press the ok button.

The unit will now scan in any Free-To-Air channels you don’t already have.
TV3 will most likely appear on the end of you existing channels.
You can organize the channels now if you wish.

Organize Channels

The Steps to reorder the Channel Listing are as follows

1. Press the Menu button to access the main menu
2. If prompted enter the pin code (default is 0000)
3. Select Channel and press OK
4. Select TV Channel and press OK
5. Press the Yellow button on your remote (Edit)
6. If prompted enter the pin code (default is 0000)
7. Select the channel you want to move and press the White button on the remote
 (Some models of remote do not have a white button on these press the subtitle button)
8. Use the up and down arrows on the remote to scroll to where you want to place the channel
9. Press OK to move the channel to the new location

Repeat steps 7-9 for each channel you want to move

Once all channels have been moved press the Exit button once.

It will say Do you want to save?
Move across to highlight OK and press your OK button to save the changes.

John Jenkins said:

Hiya Josh...I printed out those same instructions this morning,they don't work...

I press menu..pressing the left arrow does nothing.and that's as far as I can go,I note that the

"Dish'' S7010 is not included in the list

regards jack

• ▶ Reply

Permalink Reply by John Jenkins on July 7, 2016 at 9:25

Hiya I`ve tried your suggested fix but still only have sound for TV 3

Regards Jack

Paul said:

Try this instead

How to Tune TV3 in on Your DishTV S7000/S7010

Go to Main Menu>Installation>Installation
(At the bottom of your screen you should have Level and Quality bars)

Then push the red button on your remote (this will do a single scan)
Use the left and right arrows on each line to make it look like below.

Scan Mode Free
Program Type TV
Scan Type Manual Scan
NIT Search Off

Then press the ok button.

The unit will now scan in any Free-To-Air channels you don’t already have.
TV3 will most likely appear on the end of you existing channels.
You can organize the channels now if you wish.

Organize Channels

The Steps to reorder the Channel Listing are as follows

1. Press the Menu button to access the main menu
2. If prompted enter the pin code (default is 0000)
3. Select Channel and press OK
4. Select TV Channel and press OK
5. Press the Yellow button on your remote (Edit)
6. If prompted enter the pin code (default is 0000)
7. Select the channel you want to move and press the White button on the remote
 (Some models of remote do not have a white button on these press the subtitle button)
8. Use the up and down arrows on the remote to scroll to where you want to place the channel
9. Press OK to move the channel to the new location

Repeat steps 7-9 for each channel you want to move

Once all channels have been moved press the Exit button once.

It will say Do you want to save?
Move across to highlight OK and press your OK button to save the changes.

John Jenkins said:

Hiya Josh...I printed out those same instructions this morning,they don't work...

I press menu..pressing the left arrow does nothing.and that's as far as I can go,I note that the

"Dish'' S7010 is not included in the list

regards jack

• ▶ Reply

▶ Reply to Discussion