Does anybody have the instructions for tuning a Kaon Satellite Receiver Model KSF-270 to receive TV3.  I can still watch the TV3+1 channel just not TV3 itself?

Views: 2558

Reply to This

Replies to This Discussion

Try the below , please let us know if this works :)

You can use the following method to re-scan channels on the KSF-270 if you have lost some channels:

1. Press Menu
2. Select Installation press OK
3. Enter PIN if requested. Default PIN is 0000
4. Move to "Optus D1" satellite and ensure "Optus D1" is highlighted in blue.
5. Press the Green button on the remote control to list the transponders.
6. Move to transponder labelled, "12456 22500 .." and ensure it is highlighted in blue.
7. Press the OK button to select the transponder. When selected, a "tick" will appear next to it.
8. Press the Red button on the remote control to show the scan popup menu.
9. Change "Network" to "on". Use the left and right arrow buttons to change the settings.
10. Press the OK button to scan. Allow the scan to finish.
11. Once the scan is finished, the number of new TV and Radio channels found will be shown.
12. Press OK to exit
13. Press OK to Save the channels found
14. Press Exit to exit the Menu
15. Check if you have all the channels.

The KSF-270 has "Automatic Freeview Install". You can reinstall the channels via a factory reset and then retune.

1. Press Menu
2. Select System Settings press OK
3. Enter PIN if requested. Default PIN is 0000
4. Move down to Factory Reset
5. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
6. Select Menu Language and press OK
7. Select Audio Language and press OK
8. Select Subtitle Language and press OK
9. Set the Time to GMT+12:00 and press OK ( we are currently GMT+12:00 and during daylight savings GMT+13:00 )
10. Select the closes location from the list and press OK
11. Select "Automatic Freeview Installation"
12. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
13. Press OK to exit
14. Press OK to Save the channels found
15. Press Exit to exit the Menu
16. Check if you have all the channels.


Hi Paul

Thanks very much for instructions.  Followed them and now have all my channels back.  Thanks for helping, much appreciated.

Regards

Christine


Paul said:

Try the below , please let us know if this works :)

You can use the following method to re-scan channels on the KSF-270 if you have lost some channels:

1. Press Menu
2. Select Installation press OK
3. Enter PIN if requested. Default PIN is 0000
4. Move to "Optus D1" satellite and ensure "Optus D1" is highlighted in blue.
5. Press the Green button on the remote control to list the transponders.
6. Move to transponder labelled, "12456 22500 .." and ensure it is highlighted in blue.
7. Press the OK button to select the transponder. When selected, a "tick" will appear next to it.
8. Press the Red button on the remote control to show the scan popup menu.
9. Change "Network" to "on". Use the left and right arrow buttons to change the settings.
10. Press the OK button to scan. Allow the scan to finish.
11. Once the scan is finished, the number of new TV and Radio channels found will be shown.
12. Press OK to exit
13. Press OK to Save the channels found
14. Press Exit to exit the Menu
15. Check if you have all the channels.

Hi Anil

Thanks very much for information and instructions for a factory reset, much appreciated.  Will print them off and keep them in case I need them.  Had already reinstalled channels using Paul's instructions but haven't been near my laptop for a few days to reply and say that the instructions he gave worked fine.

Regards

Christine


Anil Hari said:

The KSF-270 has "Automatic Freeview Install". You can reinstall the channels via a factory reset and then retune.

1. Press Menu
2. Select System Settings press OK
3. Enter PIN if requested. Default PIN is 0000
4. Move down to Factory Reset
5. Press OK to confirm Factory Reset. The receiver will restart and show the Easy Setup Menu
6. Select Menu Language and press OK
7. Select Audio Language and press OK
8. Select Subtitle Language and press OK
9. Set the Time to GMT+12:00 and press OK ( we are currently GMT+12:00 and during daylight savings GMT+13:00 )
10. Select the closes location from the list and press OK
11. Select "Automatic Freeview Installation"
12. Once the search is complete the number TV and Radio channels found will be shown. Press OK to continue.
13. Press OK to exit
14. Press OK to Save the channels found
15. Press Exit to exit the Menu
16. Check if you have all the channels.

Reply to Discussion

RSS

NETWORK STATUS ALERTS

TVHB is temporarily off-air.

28 Mar: Issue affecting some channels in Auckland,

ALL OTHER PLATFORMS WORKING WELL.  See Network Status for more info and updates.

Quick Links

© 2021   Created by Bel @ Freeview.   Powered by

Badges  |  Report an Issue  |  Terms of Service