Rescan on VEON SAT101

The following instructions are supplied by the manufacturer and extracted from the VEON SAT101 website.

With some channels being transmitted from a Sky transponder, the device may require an update to locate the new transponder.

MANUAL UPDATE

The following instructions are supplied by the manufacturer and extracted from the Dish TV website.

With some channels being transmitted on a Sky transponder, the VEON SAT101 may need a rescan to locate the transmission.

The steps to do this are as follows:

  1. Press the menu button on the remote to bring up the main menu
  2. Select Installation and Press Ok
  3. Select Factory Default and Press Ok
  4. Enter the pin code for the receiver (The default is 0000)
  5. Select Yes and press OK

After the factory reset process has completed you will be prompted to select your region and press ok.

Once the scan process has completed you should have access to all channels again. In some cases this process will not correctly add PRIME, BRAVO plus 1 & THE EDGE TV, you will need to then manually enter the Transponder details for PRIME, BRAVO plus 1 & THE EDGE TV.

The steps to do this are as follows

1.    Press the Menu button to bring up the main menu

2.    Select Installation and press OK

3.    Select Tuning Wizard and press OK

4.    Enter the PIN code for the unit (the default is 0000)

5.    Select Satellite Scan and press OK

6.    Press the left arrow to access the carrier list

7.    Press the Yellow button to access the Setup menu

8.    Select Add Carrier and press OK

9.    Enter 12519 for the Frequency

10.  Select Symbol rate and enter 22500

11.  Check that Polarity is set to Horizontal

12.  Check that network scan is set to Off

13.  Press OK to start the Scan process

The scan process will take approximately 1 minute to complete.

Once the scan process is completed you will be returned to the Satellite Scan menu.

Press Exit to return to watching normal TV.

Once the scan process is completed press Exit to return.

Successfully completed, you should no longer see a message appear every 30 minutes on-screen on PRIME, BRAVO plus 1 or THE EDGE TV between noon and midnight each day.

Manufacturer Support

If you have problems with successfully carrying out this process, please see here for more information or contact the manufacturer Dish TV here.

Add a Comment

You need to be a member of freeview forum to add comments!

Join freeview forum

Comment by Richard Smith on June 2, 2016 at 19:24

Thanks David but I don't think it's that simple for me as I'm still getting the warning messages on Prime. Any other suggestions anybody?

Comment by David Lipscombe on May 30, 2016 at 21:26

Richard if your test3 shows prime you may have to just edit this and change the name to prime , I had the same thing happen t me on Four +1 prime and the edge tv and now they are working fine after I did the renaming

Comment by Richard Smith on May 30, 2016 at 17:40

PS My Freeview device is a VEON SAT101

Comment by Richard Smith on May 30, 2016 at 17:39

I followed the instructions as described above and am still getting the message saying that I need to retune. Prime appears as Test 3 on the Channel list.

Comment by forumuser on May 29, 2016 at 19:06

Hi Graham, 

I have now sent you a private message 

Regards, Josh Hill

Comment by Graham Burgess on May 29, 2016 at 16:01

This morning, without instructions from me, my Veon Sat101 updated all by itself, albeit with the channels in funny places, ie Prime instead of being channel 10 is now 14. Is this to be expected or have I stumbled upon the black arts?

Comment by Graham Burgess on May 28, 2016 at 17:15

Have followed instructions twice so far, still getting message and Prime is called "Test3"

NETWORK STATUS ALERTS

See Network Status page for updates.

Freeview On Demand Changes Read More Here

Quick Links

© 2024   Created by Bel @ Freeview.   Powered by

Badges  |  Report an Issue  |  Terms of Service