We have a two year old Freeview enabled Panasonic Viera TV. Our reception is UHF, line of sight to Mt Kaukau in Wellington. All was working well until a few weeks before Christmas when we began to suffer pixelation on TV3. It has gotten progressively worse and now that the holidays are almost over I'd like to try to sort the problem.

I've also looked at Bravo and the +1 versions of both. All are pixelated. There is no problem with other stations. I have also used the TVs facility to check the signal condition. The TVNZ stations and Prime all score 8 or 9/10. Maori scores 6/10. The Mediaworks stations score 4/10. This clearly suggests a problem with the Mediaworks MUX.

The problem may be with the tv but I am curious if there has been any changes that may have impacted the quality of the signal for the Mediaworks stations. Any suggestions are greatly appreciated.

jh

Views: 390

Reply to This

Replies to This Discussion

Almost certainly a problem with your antenna and/or cabling. Natural deterioration  of both due to effect of weather can cause this problem. The signal strengths may be OK but what are the readings for quality?

Yes, it is the quality that is low. The strength is 5/10 for everyone.



Biggles said:

Almost certainly a problem with your antenna and/or cabling. Natural deterioration  of both due to effect of weather can cause this problem. The signal strengths may be OK but what are the readings for quality?

OK. Then something in the house or nearby may be affecting the quality. Difficult to locate but logical thing to do is turn everything in the house off and then check signal/quality. Start turning things on to locate any interference or quality reduction. Cordless phones and some modem can be a problem if located near the TV or coax cable. Also a poor quality lead from wall socket to TV can cause signal loss and/or quality loss. I've had brand new ones that didn't work at all back in the days of analogue TV. A cellphone band filter in-line may help. If your antenna has direct line of sight to Kaukau then all MUX should be 100% signal and 100 or lss quality.

What sort of antenna and coax is in use? Anything older than 5 years may need attention. I'm in Auckland and you wouldn't believe the amount of salt spray contamination deposited on things which causes corrosion. Wellington is probably worse.

Thanks for this. We needed to install a cell phone band filter at our holiday home after they put in a new line of site cell tower. (Advantage was that we no longer have to stand in just the right place to make a call :-)) Something like this may be the problem. I'll follow up in this direction tomorrow.

jh

Biggles said:

OK. Then something in the house or nearby may be affecting the quality. Difficult to locate but logical thing to do is turn everything in the house off and then check signal/quality. Start turning things on to locate any interference or quality reduction. Cordless phones and some modem can be a problem if located near the TV or coax cable. Also a poor quality lead from wall socket to TV can cause signal loss and/or quality loss. I've had brand new ones that didn't work at all back in the days of analogue TV. A cellphone band filter in-line may help. If your antenna has direct line of sight to Kaukau then all MUX should be 100% signal and 100 or lss quality.

What sort of antenna and coax is in use? Anything older than 5 years may need attention. I'm in Auckland and you wouldn't believe the amount of salt spray contamination deposited on things which causes corrosion. Wellington is probably worse.

Reply to Discussion

RSS

Latest Activity

Tony Bowen replied to Tony Bowen's discussion satellite receiver stopped working
"Thanks Willis. I tried this and got the same result. Then I checked the LNB to find the plastic…"
Thursday
willis replied to Tony Bowen's discussion satellite receiver stopped working
"See if it will switch on with the satellite cable unplugged If so then cable/ lnb suspect If not…"
Thursday
clifford c wright replied to clifford c wright's discussion missing tv1,tv2, duke on freeview.
Wednesday
Tony Bowen posted a discussion

satellite receiver stopped working

Is it time for a new receiver? My Strong SRT 4300 Digital Satellite Receiver has stopped working…See More
Wednesday

Connect With Us!

© 2018   Created by Bel @ Freeview.   Powered by

Badges  |  Report an Issue  |  Terms of Service